zkxx --- 2007-05-18 10:12:07
1
我是新的設計人員，求助？？？
周永初 --- 2007-05-19 11:41:23
2
很簡單：
導體為鍍錫軟銅線，絕緣PVC，絕緣厚度0.38MM，
比如：
26AWG ID=1.3
28AWG ID=1.15
30AWG ID=1..0
24AWG ID=1.45
22AWG ID=1.6
AbelGuo --- 2007-05-22 09:06:56
3
電子線的設計導體：16-32AWG （Stranded And solid Tinned and bare）絕緣PVC 或SR-PVC 平均厚度：15Mils 最小為：13Mils
UL 758 AWM Style page 寫的很清楚�。�
luoxinqiao --- 2007-06-05 09:20:49
4
WONDERFUL --- 2007-06-14 09:32:45
5
2935316 --- 2007-06-25 14:05:09
6
去買一本標準,什么都清楚了!
youyucs63 --- 2007-07-20 16:03:12
7
由絞合好的鍍錫銅和外被組合而成,導體型號由16AWG~28AWG,外被一般都用SR-PVC,還要油印字,
呂月白 --- 2007-07-20 20:30:18
8
知道標準的行家請把相關的條款告訴一下.
免得后輩花了大量的精力還是沒有整明白.
還不如前輩們稍微指點一下就明白了~
是不是?
沙漠駱駝 --- 2009-01-19 11:06:41
9
平均厚度：15Mils 最小為：13Mils,這是標準厚度呀,跟我們所說的0.40mm有什么不同呀
wuxuner --- 2009-03-09 14:04:39
10
szss73 --- 2009-04-27 15:25:56
11
lluu --- 2009-04-27 18:27:16
12
不一定哦,要看你申請的時候授權給你做多厚才行哦!
jimwang --- 2009-05-05 22:38:09
13
1007是最簡單的線，80度300V的，15MIL平均厚度，13MIL最小厚度，你沒有通過認證是不能做的，只有通過認證才可以印UL標志的
jizhuan501 --- 2009-05-06 09:23:05
14
這屬于電子線，相對比較簡單點兒！
hushao --- 2009-05-06 11:28:50
15
UL style page
yy2008 --- 2009-05-06 11:41:39
16
對UL758活頁里面對該款線材的結構、檢驗、檢查要求寫得很清楚的，
是設計、生產、檢驗、檢查的依據。
LWGXINYA --- 2009-05-08 10:00:31
17
像這種簡單的問題，看看別的公司或自己公司的產品目錄，照個葫蘆畫個瓢就可以了
ceteight --- 2009-05-08 15:31:57
18
這個線是電線入門最基本的線材了，多看看別公司產品就會了。
做電線的 --- 2009-05-08 18:32:47
19
對頭。。�？纯磩e家公司的產品目錄一下就知道了
推薦看看樂庭的。。。
做的挺全的
芝麻開門了 --- 2009-05-11 17:21:05
20
到百度上搜一下，上面都有的。1007是最基礎的線材，線徑基本都已經在業內通用了。
Kining --- 2009-05-15 11:24:45
21
UNDERWRITERS LABORATORIES INC. APPLIANCE WIRING MATERIAL
Subject 758 Section 1 *Page 1007 Issued: May 1, 1959
Revised: June 20, 2001
Style 1007 Polyvinyl Chloride Insulated Wire.
____________________________________________________________________________
Rating 80°C, 300 V.
____________________________________________________________________________
Conductor 32-16 AWG, solid or stranded.
____________________________________________________________________________
Insulation Polyvinyl Chloride, 15-Mils minimum average,
13 mils minimum at any point, 60 or 80°C in oil,
if applicable.
_____________________________________________________________________________
Standard Appliance Wiring Material UL 758.
_____________________________________________________________________________
Instructions Detailed Examination.
to UL Physical Properties, unaged.
Representative Spark Test.
_____________________________________________________________________________
UL (4) Detailed Examination.
Counter-Check (4) Physical Properties.
Program (4) Heat Shock.
(4) Cold Bend
(4) Horizontal Flame Test.
(4) Deformation.
_____________________________________________________________________________
Marking General.
_____________________________________________________________________________
Use Internal wiring of Appliances; or where exposed to oil at
a temperature not exceeding 60°C or 80°C, whichever is
applicable. Tags may indicate the following: 600 V Peak -
For Electronic Use Only.
Kining --- 2009-05-15 11:26:02
22
lwlmuzi520 --- 2009-05-15 15:23:48
23
| UNDERWRITERS LABORATORIES | APPLIANCE WIRING MATERIAL |
| Subj.758 | Section 1 | Page 1007 | Issued:1959-05-01 |
| Revised:2008-05-27 |
| Style 1007 | Insulated Wire. |
| Rating | 80 deg C, 300 Vac, Horizontal flame, Oil Resistant 60 deg C or 80 deg C (optional). |
| Conductor | 32 AWG - 16 AWG Solid or Stranded. |
| Insulation | PVC, 15 mils minimum average, 13 mils minimum at any point. |
| Standard | Appliance Wiring Material UL 758. |
| Use | Internal wiring of appliances; or where exposed to oil at a temperature not exceeding 60 deg C or 80 deg C, whichever is applicable. Tags may indicate the following: 600 V Peak - For Electronic Use Only. |
yy2008 --- 2009-05-15 16:40:01
24
贊成3樓意見,
AWM活頁是ULAWM電線設計、生產、檢驗、檢測、認證的依據.